Monthly Archives: March 2011

How to Stain Concrete

I thought I would share this with you.  Decorative Concrete Supply in Lenexa had a great write up about staining concrete in a recent newsletter I got.  Enjoy!!

4 Basic Steps to Staining
     Concrete stains, both reactive (acid stain) and non reactive (water based), enjoy wide spread popularity among designers and home owners.  Whether you are veteran professional applicator or a first timer, understanding the basics is vital to achieving good results. Let’s review the four basic steps to staining, and the proper procedures for each. Almost all stain problems can be eliminated by following these steps. 

1. Surface preparation: Understanding what the concrete is going to do once the stain is applied is very important. Proper surface preparation can save you a lot of headaches down the road. A simple water test (spraying water over the surface and observing what happens) is always recommended, and tells quite a bit about the porosity of the concrete and the ability for the stain to wet out and react. Look for dry spots or beading of the water. If the water does not soak in evenly, additional prep may be necessary. Dry sanding, chemical degreasers, and mineral acid cleaning are three common methods of cleaning or opening up the surface for better penetration. Conducting a moisture-vapor emission test is also a good idea at this time. This will measure how much moisture vapor is being emitted from the slab. Too much moisture could inhibit stain penetration. You can find out more about moisture testing by talking to one of the sales professionals at Decorative Concrete Supply.

2. Stain application: Applying the stain is actually the easiest of the four steps. Most stains provide a coverage rate of 250 to 300 square feet per gallon. Avoid over application, which can create surface tension or buildup, especially on less-porous concrete surfaces and when using darker stain colors. I recommend applying the stain using a good quality sprayer.   It can be a pump up type or a pressure type; the critical thing is that you have a good quality tip that sprays evenly, and does not “spit”.   Make sure to apply even thin coats, with two coats usually being sufficient.  With acid stains, allow a minimum of 5 hours of dwell time between applications.  If using a broom or scrubber to work the stain into the concrete, remember to work out any broom marks and/or streaks.   

3. Neutralizing and washing: This is the most misunderstood and overlooked step of the four, especially when acid staining. To better understand the importance of neutralizing, think of it this way: By applying an acid stain, you take concrete from a basic pH state to an acid state. You need to return the concrete to a basic state, while removing any unreacted stain and stain residue. Simply put, this step involves a good old-fashioned cleaning and scrubbing with an alkaline soap that can break down stain residue and neutralize the surface. Using water by itself is not enough. Once again, using a broom or walk-behind scrubber makes the job easier. Typically, multiple scrubbings are needed, especially with terra cotta and dark brown stains. Take a pH test to make sure the surface has been properly neutralized. Then rinse the surface with clean water and allow ample dry time before sealing.  Using water based stain makes the job much easier since there is not acid to neutralize, just make sure any remaining residue has been removed. 

4. Sealing and maintenance: The final step is to apply a sealer to the stained floor, to keep it looking and performing its best. However, if the project is an interior application, sealing by itself is not enough. It’s important to use a sealer system, which includes a base-coat sealer and a sacrificial topcoat sealer, or wax.  In the next edition we will discuss sealing after staining in detail.

Even when you follow all the steps outlined above, variations can occur. That’s why you should apply a sample of the stain for all your staining projects. This is the only way to get a good idea of what the stain will look like. For more detailed staining guidelines, consult with the stain manufacturer, or the sales professionals at Decorative Concrete Supply.   

A guide to all things polished concrete

A new blog started about polished concrete. 

A guide to all things polished concrete.

Polished Concrete Outshines Other Flooring Options – EBN: 15:2


The below is a great article I found which describes in detail polished concrete as compared to some other flooring choices.

Polished Concrete Outshines Other Flooring Options – EBN: 15:2.

I hope this article gives you some insight on polished concrete flooring.